Sv 360 Premier

admin



From Free Knowledge Base- The DUCK Project: information for everyone

This sonicview sv 360 premier, as one of the most functioning sellers here will categorically be in the middle of the best options to review. BookGoodies has lots of fiction and non-fiction Kindle books in a variety of genres, like Paranormal, Women's Fiction, Humor, and Travel, that are completely free to download from Amazon. Sonicview 360 Premier Sv-360 Sv360 PVR FTA Receiver Bonus. Ratings and Reviews. 16 product ratings. 1st - The Sonicview 360 Elite (For Programming, PVR, and Memory.) 2nd - The Sonicview 360 Premier (For Programming, memory, & more. Yes Sonicview is a better brand then Coolsat.

Jump to: navigation, search
  • 1SVLan Setup
  • 2Channel Setup
  • 3Support

SVLan Setup

Menu Load Method

Part 1

  1. Download and unzip latest bin to your USB drive
  2. With power off, insert USB drive into USB front port on receiver
  3. Open Menu, navigate to PVR Options, Front USB, and select the bin file from the list
  4. Choose S/W Update. Wait while file loads and updates, be patient, do not disturb receiver or thumb drive
  5. Reboot Yes when prompted

Part 2

  1. Download and install Wiznet 3.0.1 to your PC (you need this or latest version)
  2. With Sonicview on, and SVLan connected, goto PC and run Wiznet
  3. PC and SVLan on receiver must both be connected to same LAN switch or hub
  4. In Wiznet choose 'Search' and it will find your SVLan adapter via network and show the Mac Address
  5. Use Wiznet to set the IP address for SVLan (network settings appropriate for your LAN)
  6. Once set click the 'Settings' button next to the 'Search' button

Part 3

  1. Press Menu; Choose System Settings; Choose Time Settings; Choose your time zone exit.
  2. Press Menu; Choose System Settings; Choose User Options; Set all to ON Choose your local and exit.
  3. Press Menu; Choose System Settings; Choose Parental Conrol; 0000; Set all to OFF, and ACC to Disable.

Part 4

  1. Set up birds and scan for channels

Part 5

  1. Enter 'Serial Number' for SVLan

Force Load Method

How To Force Load Sonicview SV-360 Premier With USB Drive

  1. Turn the the Premier Off completely from the rear power switch
  2. Format USB flash drive
  3. Copy latest bin file fix to the flash drive
  4. Insert flash drive into premier usb port
  5. Press and hold Ok button (located on the front panel) and then turn the Premier On using the rear power switch
  6. Select the bin file and let it load

Channel Setup

FTA Setup

Charlie Testing Setup

Note: the following is theoretical, do not actually attempt this.

Sv 360 premier

first load the newest channel template file

then scan sats in this order:

  • The following settings are for TESTING purposes only. You will not be able to view any programming since the satellites described below provide only scrambled signal. However, you WILL be able to do a basic test to ensure signal is being received. For information on purchasing programming see other section.

Tuner: EchoStar 7

Tuner: EchoStar 8,10 Cube world desktop icon.

  • or any active transponder on the satellite.

Support

Files and Updates

If using an SVLan there are support files to update firmware for the Sonicview SV-360 Premier.

  • h.ttp://www.ftaforall.biz/forums/showthread.php?t=97496 FTAFORALL.net SVPremier WizHub and Lan files

note: ftaforall.us is offline, dns expired, as of Dec 2011. None of the links above are reliable or operational at this time.

Support Forums

  • (FTAforall-Receiver-Discussion) Forum section dedicated to this receiver. These guys are real forum nazis so make sure you format your post perfectly.
  • (MyFreeNeeds-Sonicview360P-Discussion) Another forum section where this receiver is discussed.

note: myfreeneeds is unreliable / often offline.

New Links:

Network Adapter Error!!!

Sonicview 360 Premier Setup

There have been many bad SVLan modules shipped. RMA if you are unable to verify successful connectivity between the SVLan and the receiver through the serial port.

Reception Troubleshooting

See Digital Ku-Band Mini Dish Frequencies and Channels for reception troubleshooting help with the well known Sonicview Transponder Off-By-One Glitch.

Retrieved from 'http://wiki.robotz.com/index.php?title=Sonicview_SV-360_Premier&oldid=9370'

Sv-360 Premier Remote Control Codes

Here are two Known and Tested Fixes for the iHub.
One is used when your iHub is connected to your Home Network (Router)
The other is for a Direct Cable Connection. (iHub is connected to computer LAN port)
There is also another - use at your own risk - method given for loading or testing what appears (or you have written off) to be a 'DEAD' iHub.
Some of us know a bad power supply, poor ground or connection can also cause iHub issues on the SV
For XP Operating System
1) Start > Control Panel > Network Connections >
2) Right Click on Local Area Connection and select properties
3) Double Click Internet protocol (TCP/IP)
4) Select - Alternate Configuration tab and Select - “User Configured”
5) Enter – IP address 192.168.11.52, subnet 255.255.255.0 and gateway 192.168.11.1
6) Exit and reboot computer
7) Put receiver in standby mode - run wiznet and it should find the iHub
8) Upload iHub version 1.9 then reboot receiver
9) Go into Receivers Menu > Installation > ipconfig
10) Set to DHCP
11) Enter serial number and hit apply
12) Reboot receiver - you should be good to go..
If so, now go back thru steps 1-4 this time select “Automatic private IP address” and reboot your computer
For Vista and Windows 7 Operating System 1) Start > Control panel > Network and Sharing Center >
2) Under Tasks Pane - Manage Network Connections >
3) Right Click - Local Area Connection >
4) Properties > Highlight - Internet Protocol Version (IPv4)
5) Select Properties Button >
6) Click Alternate Configuration Tab > Select - “User Configured”
7) Enter – IP address 192.168.11.52, subnet 255.255.255.0 and gateway 192.168.11.1
8) Exit and reboot computer
9) Put receiver in standby mode - run wiznet and it should find the iHub
10) Upload iHub version 1.9 then reboot receiver
11) Go into Receivers Menu > Installation > ipconfig
12) Set to DHCP
13) Enter serial number and hit apply
14) Reboot receiver - You should be good to go..
If so, now go back thru steps 1-6 this time select “Automatic private IP address” and reboot your computer
If you have tried the above and feel you have what appears to be a dead iHub
Kinda think you are one of the many who have written off the iHub as being 'blown'
Putting voltage to it cannot do any more harm. Right? 1) Remove the non-responding iHub from the receiver
2) Rig up a 9 volt battery to Pin 4 (+) and Protective Ground (-)
Note: The Ethernet lights on the IHUB immediately lit up
3) Open the Wiznet tool and hit search, it should immediately up came the iHub info
4) Update to iHub 1.9 5) Remove Battery Attachment and Reconnect iHub to receiver
How To - Change the default iHub IP Address to match your home network.
This will work as long as you have a router and you have a working iHub (one that lights up).
1) Connect iHub to receiver
2) Turn Main Power switch on, but leave power off from the front panel (so that only the time is displayed)
3) Connect Ethernet cable from iHub to Ethernet port on router
4) Open Wiznet and press the 'Search' button. As long as you get some sort of iHub information you are OK. Do not close WIZNET.
5) Go into your start menu, click 'RUN' - type 'CMD' hit enter - type 'ipconfig'
6) Go into WIZNET and make sure that 'Static' is checked
7) Set the 'Subnet and Gateway” to match the settings of your home network attained using the “cmd – ipconfig” above in step 5.
Here is an example of your Wiznet settings:
Local IP: 192.168.1.120
Subnet: 255.255.255.0
Gateway: 192.168.1.1
Port: 1920
Operation Mode: Mixed
USE DNS: is checked!!!
DNS SERVER IP: (DNS Server IP - is automatically populate from your service provider)
7) Set a valid (unused) IP address for the iHub using the 'Local IP' of 192.168.1. ***
Examples: (192.168.1.120) (192.168.1.130) (192.168.1.140)
7a) Click on the 'Setting' button - if it gives you an error, click 'Setting' again until it processes.
7b) Click on the 'Upload' button – Browse to the iHub1.9 file - You should instantly notice it 'Processing'.
7c) If you get a 'Failed to Upload' message - Go back to step 7
8) Once it says Completed, close Wiznet, Reopen Wiznet, Hit search, you should now see the new 1.9 version. Select DHCP, Hit settings and once processed, Exit Wiznet
9) Turn On the receiver, Load newest receiver file - Setup your 'ipconfig' with iHub serial number - Setup your 'Dish Settings' - Setup your other 'settings' - watch TV.